Honda GX35 35 cc 1.60 hp FOUR STROKE Complete kit

This is a complete kit including the engine listed above, plus the following parts that are needed to install on most bicycles:

Included

Complete Engine Assembly (clutch drum, clutch rotor, engine spacer, bearings, housing) The housing is ¼” thick Aluminum Extrusion Channel (not a bent thin piece of steel) the channel is CNC machined and anodized black.

The engine has a centrifugal clutch and is easy pull start. Honda GX35 35.8 cc 1.30 Net 1.60 Max HP Four Cycle engine, 21.76 oz fuel tank. Rear mount bike kit. Top speed 22 to 35 mph depending on the weight of the rider and the size of the drive roller that you pick. Rear mount complete friction drive Kit. This mounts to most bikes in about 20 mins

Approx 160 to 220 mpg.

The complete kit weighs about 14 lbs.

Top speed over 30 mph with the Honda GX35 depending on the size of the drive roller and the weight of the rider.

This is a full crank four cycle engine with a centrifugal clutch and super east pull start. The centrifugal clutch allows the engine to keep running while the bike is stopped, then turn the pedals 3 to 5 times and hit the throttle and take off.

Included

Drive Roller we use two high speed double sealed ball bearings, (one on each side to support the drive roller), our drive rollers are CNC machined, knurled, case hardened, zinc plated & heat treated metal. Use the drop down menu when ordering.

The smaller the drive roller the more pulling power you have, the larger the drive roller the faster top speed. We manufacture our drive rollers in 5 different sizes: .875 inch, 1.0 inch, 1.125 inch, 1.25 inch, and 1.5 inch.  This offers our customers the ability to fit our kits to accommodate every engine and virtually every rider regardless of size or riding conditions. Our drive rollers are CNC machined, heat treated & zinc plated.

Note:  Available with Your Choice of the size of the drive roller. Pick from:

The 7/8 inch is good for hills and or riders over 250 lbs. Top speed about 22 mph.

The 1 inch has a good top speed and good power for hills. Top speed about 25 mph.

The 1-1/8 inch (Standard size) is for a faster top speed about 30 and riders under 185 lbs. The 1-1/4 inch is for riders under 165 lbs and mostly flat ground, 30+ mph.

Included

The U shaped mounting bracket

Included

Engaging Rod, to raise and lower the drive roller, complete with all parts and hardware

add a Dual engaging system

Note: this kit comes with the single engaging rod; you can switch to the Dual engaging support for an additional $12.95 Some customers like one for each side. If you want the Dual engaging rods use the drop down menu, you will not receive the single rod.

Included

A 60 inch long Throttle Cable and finger / thumb lever for the throttle control. (Twist grip is extra)

You can Add a longer throttle cable or a Twist Grip throttle. Goto the Friction drive add on parts page.

Included

Remote toggle engine stop switch with handlebar mount for safety.

Included

Nuts and Bolts Plus many other small parts needed for mounting.

This kit comes complete with all the mounting hardware, stop switch and single engaging rod for a rear mount bicycle.

Most of these parts are preassembled for you.  The only parts you attach are the U bracket to the bike frame and the black housing to the U bracket, and then attach the engaging rod to the frame, throttle cable and remote stop switch.

Note: You may want other hardware that is not included in the kit depending on the style of bike. Like a longer throttle cable, Extension bracket, Twist grip throttle, Hour/Tach meter, ect…

You can Motorize any bike; we carry many PARTS for your custom installation and other size Friction Drive Engine Kits. As well as Engine Kits for Trikes. We also carry Chain Drive Engine Kits. Be sure and check out the Chain Drive Engine Kits if you need more power.

Please be sure and click on the Friction Drive GALLERY page to your left to see examples of our kits installed on various bikes and read some more information.